Friday, July 21, 2017

Frayed Wiring and Electrician

Wiring problems

Frayed

Wiring problems should be addressed for safety purposes. (Photo Credits)

Frayed wiring can be inevitable and dangerous at the same time. It has to be repaired as soon as the issue is discovered to avoid accidents and injuries.

CNET.com shared ways on how to deal with frayed cables. American Lighting Association

"You can take your time neatly wrapping the cable to reinforce it, but the best way to prevent any more damage is to wrap the split or fraying part of the cable several times with electrical tape, then work your way out from that spot. This immobilizes any breaks in the cable and helps prevent further damage. Just don't expect it to last forever."

Electrician's Tips on Fixing a Defective Light Switch

Read the rest of the write-up here.

Damaged wires

The website The Spruce also detailed ways to fix damaged insulated cables. Master Electrician   

"When working on old wiring in your home it is important to inspect the condition of the wiring's insulation. The insulation used on old wiring can fray and become brittle, literally crumbling in your hand as the wire conductor is moved. In the above photo you can see how the insulation is brittle and wiring is actually exposed. This condition is very dangerous and can create short circuits and fire hazard. Ordinarily, you can just wrap 2 or 3 wraps of electrical tape around the damaged area."

Electrician's Tips in Installing a Dimmer Switch

Read the whole material here.

Related Electrical Repair and Installation Services

This Old House meantime mentioned about aluminum wiring.

"Retrofit a dielectric wire nut approved for aluminum wire (a pair sells for less than $1) onto each copper/aluminum connection in light fixtures. These nuts have a special grease that stops corrosion while maintaining conductivity. Make sure any replacement switches and receptacles are labeled AL-compatible."

Check the rest of the guide here.

Frayed cables should be dealt with as soon as possible. If unsure of what to do, get in touch with an expert electrician contractor.

Gforce Green Electric Solutions

2920 McGraw St San Diego, CA 92117

(858) 480-6559

Gforce Circuit Breaker Repair San Diego

Electrician's Tips on Installing a Chandelier

The post Frayed Wiring and Electrician appeared first on GforceElectric.

Posted by at No comments:

Frayed Wiring and Electrician

Wiring problems

Frayed

Wiring problems should be addressed for safety purposes. (Photo Credits)

Frayed wiring can be inevitable and dangerous at the same time. It has to be repaired as soon as the issue is discovered to avoid accidents and injuries.

CNET.com shared ways on how to deal with frayed cables. American Lighting Association

“You can take your time neatly wrapping the cable to reinforce it, but the best way to prevent any more damage is to wrap the split or fraying part of the cable several times with electrical tape, then work your way out from that spot. This immobilizes any breaks in the cable and helps prevent further damage. Just don’t expect it to last forever.”

Electrician’s Tips on Fixing a Defective Light Switch

Read the rest of the write-up here.

Damaged wires

The website The Spruce also detailed ways to fix damaged insulated cables. Master Electrician   

“When working on old wiring in your home it is important to inspect the condition of the wiring’s insulation. The insulation used on old wiring can fray and become brittle, literally crumbling in your hand as the wire conductor is moved. In the above photo you can see how the insulation is brittle and wiring is actually exposed. This condition is very dangerous and can create short circuits and fire hazard. Ordinarily, you can just wrap 2 or 3 wraps of electrical tape around the damaged area.”

Electrician’s Tips in Installing a Dimmer Switch

Read the whole material here.

Related Electrical Repair and Installation Services

This Old House meantime mentioned about aluminum wiring.

“Retrofit a dielectric wire nut approved for aluminum wire (a pair sells for less than $1) onto each copper/aluminum connection in light fixtures. These nuts have a special grease that stops corrosion while maintaining conductivity. Make sure any replacement switches and receptacles are labeled AL-compatible.”

Check the rest of the guide here.

Frayed cables should be dealt with as soon as possible. If unsure of what to do, get in touch with an expert electrician contractor.

Gforce Green Electric Solutions

2920 McGraw St San Diego, CA 92117

(858) 480-6559

Gforce Circuit Breaker Repair San Diego

Electrician’s Tips on Installing a Chandelier

The post Frayed Wiring and Electrician appeared first on GforceElectric.



This first appeared on Linda Song's Tumblr
Posted by at No comments:

Thursday, July 13, 2017

Electrician’s Tips on Installing a Chandelier

Easy ways to put up a chandelier

Light #2 is up! The chandelier!

If unsure about how to install a chandelier, a professional electrician's help should be sought. (Photo Credits)

Installing a chandelier can be quite challenging, especially to those who may not have enough experience in working around the house.

Moreover, this type of light fixture is not the normal type as improper installation can be a safety hazard.

This Old House came up with a very comprehensive guide on installing chandeliers. Builders and Contractors         

"In many ways, this installation is similar to replacing other types of light fixtures, except for one significant difference: Standard electrical boxes have a maximum load rating of 50 pounds. Most full-size chandeliers are too heavy to hang from a standard box. Therefore, if your new fixture weighs more than 50 pounds, you must install an appropriate support system."

Electrician's Tips on Fixing a Defective Light Switch

Read the whole material here.

Installing a Ceiling Fixture

The Family Handyman also came up with a tutorial in hanging chandeliers and other lighting fixtures. It however was quick to remind its readers about the safety precautions they should observe in undertaking such a project. Electricians   

"If you know your wiring was installed before 1985, don't use fixtures requiring 90-degree–rated supply wires. To confirm that you have 90-degree–rated supply wire, look at the cable jacket or wire insulation. If you have plastic sheathed cable (often referred to as Romex), look for the letters NM-B or UF-B printed on the plastic sheath. If your wiring is fed through conduit, look on the wire insulation for the letters THHN or THWN-2. If you're still unsure, either call an electrician or choose a fixture that isn't labeled with a supply wire temperature requirement."

What Flickering Lights Mean to an Electrician

Check out the rest of the guidelines here.

Related Electrical Repair and Installation Services

SF Gate for its part shared a guide on how to install particularly heavy lighting fixtures.

"A heavy ceiling light fixture, like a large chandelier or ceiling fan, requires a sturdy brace to support its weight. The drywall or plaster of the ceiling is not strong enough to support the weight of the heavy fixture. While metal and plastic support braces are available, a wooden support brace can be cut and added between ceiling joists that provides ample strength for mounting a heavy ceiling light fixture or ceiling fan."

Read the guidelines here.

When unsure about lighting fixture installations, always seek the services of professional electrician contractors.

Gforce Green Electric Solutions
2920 McGraw St San Diego, CA 92117
(858) 480-6559
Gforce Electric Repair San Diego

Electrician's Tips in Installing a Dimmer Switch

The post Electrician's Tips on Installing a Chandelier appeared first on GforceElectric.

Posted by at No comments:

Electrician’s Tips on Installing a Chandelier

Easy ways to put up a chandelier

Light #2 is up! The chandelier!

If unsure about how to install a chandelier, a professional electrician’s help should be sought. (Photo Credits)

Installing a chandelier can be quite challenging, especially to those who may not have enough experience in working around the house.

Moreover, this type of light fixture is not the normal type as improper installation can be a safety hazard.

This Old House came up with a very comprehensive guide on installing chandeliers. Builders and Contractors         

“In many ways, this installation is similar to replacing other types of light fixtures, except for one significant difference: Standard electrical boxes have a maximum load rating of 50 pounds. Most full-size chandeliers are too heavy to hang from a standard box. Therefore, if your new fixture weighs more than 50 pounds, you must install an appropriate support system.”

Electrician’s Tips on Fixing a Defective Light Switch

Read the whole material here.

Installing a Ceiling Fixture

The Family Handyman also came up with a tutorial in hanging chandeliers and other lighting fixtures. It however was quick to remind its readers about the safety precautions they should observe in undertaking such a project. Electricians   

“If you know your wiring was installed before 1985, don’t use fixtures requiring 90-degree–rated supply wires. To confirm that you have 90-degree–rated supply wire, look at the cable jacket or wire insulation. If you have plastic sheathed cable (often referred to as Romex), look for the letters NM-B or UF-B printed on the plastic sheath. If your wiring is fed through conduit, look on the wire insulation for the letters THHN or THWN-2. If you’re still unsure, either call an electrician or choose a fixture that isn’t labeled with a supply wire temperature requirement.”

What Flickering Lights Mean to an Electrician

Check out the rest of the guidelines here.

Related Electrical Repair and Installation Services

SF Gate for its part shared a guide on how to install particularly heavy lighting fixtures.

“A heavy ceiling light fixture, like a large chandelier or ceiling fan, requires a sturdy brace to support its weight. The drywall or plaster of the ceiling is not strong enough to support the weight of the heavy fixture. While metal and plastic support braces are available, a wooden support brace can be cut and added between ceiling joists that provides ample strength for mounting a heavy ceiling light fixture or ceiling fan.”

Read the guidelines here.

When unsure about lighting fixture installations, always seek the services of professional electrician contractors.

Gforce Green Electric Solutions
2920 McGraw St San Diego, CA 92117
(858) 480-6559
Gforce Electric Repair San Diego

Electrician’s Tips in Installing a Dimmer Switch

The post Electrician’s Tips on Installing a Chandelier appeared first on GforceElectric.



This first appeared on Linda Song's Tumblr
Posted by at No comments:

Friday, July 7, 2017

Electrician’s Tips in Installing a Dimmer Switch

The Benefits of a Dimmer Switch

I installed that dimmer switch.

Installing a dimmer switch at home. (Photo Credits)

Dimmer switches can be very useful around the home, and it is more so appealing to execute accent lighting around the house. American Lighting Association

The website How Stuff Works explains how dimmers function. "When you're furnishing a home, light is everything. The light level in a room dictates what you can and can't do, and it has a huge effect on how you feel. You can't read very easily by a single candle, for example, and a romantic dinner for two isn't so romantic under a 1,500-watt halogen lamp. The problem is that people need to use some rooms for multiple purposes, and these different functions call for varying amounts of light. Enter the dimmer switch, a handy electrical component that lets you adjust light levels from nearly dark to fully lit by simply turning a knob or sliding a lever."

Electrician Hacks Every Homeowner can Benefit from

Read the whole article here.

Dimmer Switch Installation Guide

Family Handyman offered a step-by-step instructional guide on how to install dimmer switches, complete with photos and a summary of needed materials and tools. Master Electrician     

"The tools you'll need are inexpensive and will come in handy for all your electrical projects. You'll need a screwdriver, wire stripper, inexpensive voltage tester and needle-nose pliers to install a dimmer. To begin, turn off the power and double-check for hot wires in the box. Turn on the light and have a helper watch as you switch off the circuit breakers, or unscrew the fuses one at a time until the light goes out. Leave this circuit turned off while you work."

Different Types of Electrical Cords of an Electrician

Check out the rest of the guide here.

Related Electrical Repair and Installation Services

The DIY Network also shared its own version of dimmer switch installation guide.

"Installing a dimmer switch is just as easy as installing a single-pole switch, and adjustable overhead lighting is a great improvement that adds appeal to any home. Turn off the power to the circuit at the circuit breaker or fuse box. Double check to ensure that it was turned off by flipping the switch in an attempt to operate a light, and by using a voltage tester to confirm that the wires in the box are not charged once the switch plate has been removed."

Read the rest of the steps here.

When unsure about installing a dimmer switch, one can always hire the services of a licensed electrician contractor.

Gforce Green Electric Solutions
2920 McGraw St San Diego, CA 92117
(858) 480-6559
Gforce Electrical Panel Upgrade San Diego

Electrician's Tips on Fixing a Defective Light Switch

The post Electrician's Tips in Installing a Dimmer Switch appeared first on GforceElectric.

Posted by at No comments:

Electrician’s Tips in Installing a Dimmer Switch

The Benefits of a Dimmer Switch

I installed that dimmer switch.

Installing a dimmer switch at home. (Photo Credits)

Dimmer switches can be very useful around the home, and it is more so appealing to execute accent lighting around the house. American Lighting Association

The website How Stuff Works explains how dimmers function. “When you’re furnishing a home, light is everything. The light level in a room dictates what you can and can’t do, and it has a huge effect on how you feel. You can’t read very easily by a single candle, for example, and a romantic dinner for two isn’t so romantic under a 1,500-watt halogen lamp. The problem is that people need to use some rooms for multiple purposes, and these different functions call for varying amounts of light. Enter the dimmer switch, a handy electrical component that lets you adjust light levels from nearly dark to fully lit by simply turning a knob or sliding a lever.”

Electrician Hacks Every Homeowner can Benefit from

Read the whole article here.

Dimmer Switch Installation Guide

Family Handyman offered a step-by-step instructional guide on how to install dimmer switches, complete with photos and a summary of needed materials and tools. Master Electrician     

“The tools you’ll need are inexpensive and will come in handy for all your electrical projects. You’ll need a screwdriver, wire stripper, inexpensive voltage tester and needle-nose pliers to install a dimmer. To begin, turn off the power and double-check for hot wires in the box. Turn on the light and have a helper watch as you switch off the circuit breakers, or unscrew the fuses one at a time until the light goes out. Leave this circuit turned off while you work.”

Different Types of Electrical Cords of an Electrician

Check out the rest of the guide here.

Related Electrical Repair and Installation Services

The DIY Network also shared its own version of dimmer switch installation guide.

“Installing a dimmer switch is just as easy as installing a single-pole switch, and adjustable overhead lighting is a great improvement that adds appeal to any home. Turn off the power to the circuit at the circuit breaker or fuse box. Double check to ensure that it was turned off by flipping the switch in an attempt to operate a light, and by using a voltage tester to confirm that the wires in the box are not charged once the switch plate has been removed.”

Read the rest of the steps here.

When unsure about installing a dimmer switch, one can always hire the services of a licensed electrician contractor.

Gforce Green Electric Solutions
2920 McGraw St San Diego, CA 92117
(858) 480-6559
Gforce Electrical Panel Upgrade San Diego

Electrician’s Tips on Fixing a Defective Light Switch

The post Electrician’s Tips in Installing a Dimmer Switch appeared first on GforceElectric.



This first appeared on Linda Song's Tumblr
Posted by at No comments:
Subscribe to: Posts (Atom)